Dodgy Shift and Tranny Ruminations 
You know...I was looking around in a box I brought up from PA...and there are 3 bottles (albeit 13 years old...) of MT90 that I had (damn memory fails me sometimes) from my last go round with a Europa resurrection. Thinking it's past its 'use by' date...IIRC, it did quiet the 336 I was running at the time and just kept on topping it up (I had leaky outputs I never got around to changing before selling her off...).

Cross member out...yeah...release the rear mount to the frame, remove mount from tranny, remove the half shafts, disconnect the shift mechanism, disconnect clutch, remove starter, free up bell housing...and out...at least that's what I'm thinking.

Now, to order the clutch parts. Previous message mentioned weak/dying spring fingers on the pressure plate. Figure, if you go with fresh stock replacements...it should work as the manual says, right?

I still have wiggle of the universal on the shift shaft (the rest of the mechanism is tight; new top hats on the shift, new bushing and top hats on the intermediate joint, rose joint at the mid-point has no play...) but that fitting at the end that captures the shift rod is not as tight as it should be. Somewhere along the line, a (d)PO honked out the holes for the pin that is supposed to be there and resized to put in a bolt. A couple folks suggested one of three solutions (besides shooting the (d)PO): 1. Tap the through-hole in the shift rod to accept an AN5 bolt that will be used to pull the female portion tight up against the shift rod, and pack the other side with a proper thickness shim, or 2. Tap the top side of the universal that attaches to the rod to an AN5 (or 4...have to measure what's in there now) thread and pull the universal tight against the rod (same idea, just from the other side), or 3. tap the shift rod, bore out the universal (this is assuming that my shift rod is 13mm) to 15mm, insert a 15/13 brass sleeve, drill out, and bolt up from both sides.

Damn (d)POs. That spirol pin worked just fine; drilling out to put a bolt in was NOT the right fix if there was slop. Sigh.

[ add comment ] ( 95 views )
Clutch Comments 
EuropaTC opined:
"The clutch sounds like mine was before I replaced it. A sharp action and sometimes difficult to start/change smoothly on the 352 box.

When I took it apart there wasn't a great deal of wear on the plate so I put it down to weakening springs. Replacing the complete assembly sorted it out though."

I replied:
Ordered the bits to do just that. I replaced the cable this morning, and adjusted per the manual (1mm free play at the tranny end...) and it never seemed to disengage (and engaging was ummmm noisy). You may have hit on the solution; weak springs just don't pull the pressure plate away but just bend instead of pulling the pressure plate back. If it's not one thing, it's another.

Thanks for the insight. According to the manual, you can pull the tranny without pulling the lump (though doing that would let me get to all the leaky bits...and clean the chassis well...). And, as a bonus, without that weight in the back, I could easily get the arse end up high enough to swap in my new gas tanks...well...will adjust the cable a little tighter and see if I can at least get it a bit more driveable.

[ add comment ] ( 100 views )
Post Brake Bleed Success 
Well...went down the road today. Eezbleed works great; took longer to get the car up on stands and wheels off than it took to bleed the system, 3 times around the car. Full pedal now. Yes, a bit higher pedal effort than I'm used to...but the car stops straight.

But...has a real fierce clutch; either on or off, and little slip. Thinking of stocking up on the bits I need to replace it. And...downshifts from 4-3 get a little crunchy...going to refresh the gear oil with new and see if that helps clear...if now, will be searching for a wrench (on this side of the fence) who can work on the x65 transaxle. After 50 years and 50K+ miles...may be time to refresh the synchros. For now...double clutch on the way down seems to work ok. Not the first car I've had to do that with.

And..it's obvious that the bushings need to be looked at...and perhaps a new set of shocks all around (I have euro length springs for the front from a previous disassembly...so will get the nose down where it belongs) and bushings.

New clutch cable on the shelf with the engine-mounted bracket at the ready...so, that will be this week's chore to take care of.

Two steps forward...and none really in the reverse direction. A good Europa day, all in all.

[ add comment ] ( 104 views )
Progress du Jour, Continued 
Not being too worried about incremental weight...for a road car (unless it is things like an extra 40 lbs of dead weight at the far back end of the car, hence my moving the battery back to where it belongs/was designed to sit near the middle), the alternative is to use twist-lock fasteners (southco, from aircraft spruce) into the rubber mounts (I have a few spares from when I updated my aircraft cowling attachment). For whatever reason, on one of my previous, when I went over a bump, because the sides were a bit weak, the box would drop down into the rear. Of course, I was also carrying 50 lbs of tools and assorted crap in the box (this was in my first europa).

My last (693R), I just cut some 1/2" dowels, painted them black, and cut to length to fit into the corners of the opening down by the drain holes. Made them up after my first car show where I just used the prop rods to open up the boot and bonnet for display, and the sun helped warp both the bonnet and boot lids...had to prop them from the other side and leave the car in the sun to warp them back. Learned my lesson; two rods for the boot, two for the bonnet, and stashed them when not using along the passenger seat and tunnel.

Lots of ways to skin this. I like the idea I saw along the way; someone replaced the pins in the rear hinge with clips that you could pull out and remove the lid entirely. THAT would make access, if you were diving into the engine room, even easier while still allowing you to open and close the lid as normal. Of course, I'd add in a forward facing lip at the front flange so that curious evildoers couldn't pop the pins and remove the lid when you weren't looking..

[ add comment ] ( 107 views )
Progress du Jour 
Got a lot more room in back of the rear cross-member now. Helps to move the battery to where it belongs. Lost about 5' of positive battery cable (hey, every little bit, even at that gauge of wire, helps). Reterminated both the positive and ground cables, Penetrox on the bare wire before attaching the new battery terminals. Cleaned up the frame end (actually, it's attached to one of the bell housing bolts) of the ground. Threw a quick leveling charge on the battery (yeah, they come charged...but aren't harmed by leveling it.). Waiting for the bolts to come in to the local NAPA store to build the hold-down clamp, but, since she's up on stands right now...it's just sitting in place.

So...now have a spare tray that is built to hang on the cross member and pick up the tranny mount bolt on the rubber isolator on the same side. Toss? Mount a waterproof box on it and use for tool caddy? Give away? Decisions, decisions.

And...getting things lined up for the next project. Caliper rebuild. New greenstuff pads. new flex hoses. Then Eezbleed the system to see if I get pedal. If not, and it's a roached MC...have an F10 and Spitfire to choose from. But...that's the "next on the agenda". Oh, yeah, put new floor and under the seat carpets in a couple days ago. Not the same weave, and the existing is a bit faded...but, for now...it looks ok and I can live with it for a while.

New dashboard was delivered (thanks, Richard!) to my PA residence...will bring back on next trip up here...and successfully removed the "Special 142" badge without ruining it. Somethings sometime just work out.

[ add comment ] ( 101 views )
More Steering Column Happiness 
In the clamp that attaches the steering column to the bracket at the bottom of the dash (and is attached to that clamp with 2 7/16 nuts on the top of the bracket...below) there is supposed to be a spring steel secondary clamp that's captured inside the two pieces that grips the column when you tighten the clamp down. It's also frequently missing especially if (d)POs took the clamp apart and the spring steel went walkabout. In maybe 50% of the columns I've taken apart...it was missing. The column should not be loose in the clamp, that spring steel fitting helps stabilize it.

I agree it is a PITA to get to those 2 nuts (especially if folks haven't dressed the wires properly...and have routed various wires under or around the column). Patience helps...lol...

[ add comment ] ( 106 views )
Battery Movement 
Want to move the battery from its position (in photo below) back to where it belongs. Found that the long bolts were still in the location where they needed to be...and want to get rid of the weight behind the wheels...not that I'll be doing any slaloms or autocrossing, mind you, but...and move it back to where it belongs.

Of the top of the head, anyone recall what the proper size is that will fit in the location it was designed for or should I just take measurements and dig through what's at the local parts emporium? Figured I'd ask first...(and have to make the hold-down channel...I have angle aluminum channel, so, that won't be a big issue to cut and drill for the hold-down....).

FWIW, pulled the heat shield out, degunked it, polished it up...ok, the rest of the fiberglass body in that location is very greasy from all the oil leaks, but, if you clean as you go...it starts to look better (that's what I tell myself as I'm digging grease and ick out from under my fingernails....)

[ add comment ] ( 101 views )
Balancing Carbs  
I'd have to dig out my balancer sticks from the storage shed in PA and bring them up. Used them last time I remember back in 06 or 07 on my CB750F4 to set the carbs up. That was going to be my next step. The feeds back from the (disconnected) charcoal canister to the base of the carbs are there (but blocked off) so it would be easy to get a vac signal there. In fact...have 2 of the Smiths dash-mounted vacuum gauges...maybe plumb them in today and see if that works. Hey, couldn't hurt, right?

Swapped in a second tach from my box o'spares collected over the years; they're within 100 RPM of each other, so pretty sure what I'm getting is what I'm getting.

Oh, I know it can be done...with time and thought. So...was more pleased that the thing reliably starts and runs at SOME speed for now; will work on the fine touches as time goes on...But pretty sure this engine is not on the young end of its life, but past middle age into its dotage...and in need of an "out-of-body experience" after this season is done and I get a few miles on her. This is just an interim, not a final destination.

[ add comment ] ( 113 views )
Half Step Back 
Saturday 30 April:

Well, spent some quality time on 3291R. New dizzy, low resistance coil, still futzing with those blasted strombergs with the euro needles, but, set for 10 degrees advance…kicks right over.

Got to loose 500 rpm somewhere. Emission plate in the engine room says timing at idle is supposed to be tdc, static 5 degrees (but the pertronix-II can’t be set statically.). Thoughts? Never replaced the throttle shaft seals...maybe that's the last step (though, squirting ether around the base of the carbs or at the ends of the throttle shafts produce no change in idle...and my plugs say that I'm still rich.) Oh well...sort it out...may be that I've not cleaned out the cylinders with a good hard run down the superslab...got to wait to finish the brakes...)

And looks like the oil leak is from the head drain tube in back of the carbs…crappy job to replace in situ…and from the oil pan area at the front left.

Have new oil pan gaskets…but that means dropping the exhaust. Always 2 steps forward, one back…But coolant level is steady, engine runs smooth…albeit idle at 1200…lol.

I have the US needles…was thinking of swapping them in and see if it makes a difference.

Update:

Sunday 1 May:

More digging around. And, discovered a couple things along the way:

1. The oil pan bolts were uniformly loose. Like some at least a quarter turn loose. So...7/16 on an extension, rear of car on jack stands, and tightened them all nice an snug. Probably NOT to the torque value in the book, but not loose either. We'll see if that slows down the puddle of dino juice on my garage floor. But as a fellow lister sent in an email...if a Ford block is not leaking, it's because it's empty...lol. Also used a pair of mole grips (channel locks) and twisted the drain tube a bit. That seems to have slowed down the leak, but still have a new one, and put it in a pan of boiling water to see if that loosens it up a bit so I can compress and get into its position in situ. Seems to work ok, don't want to have to pull the head if I don't need to just to replace a rubber fitting...but have a line on a freshly overhauled head nonetheless, so...

2. Took the pistons out of the carbs, set needles to their lowest setting referenced to the BRASS fholder, not the nylon washer. Was going to swap in what I thought were the set of US emission needles, but one had a tag on it that said "BAD". So much for that idea. Ordered a set from Ray with some other stuff...Put all back together. Idles at 1050 or so now, if the tach can be trusted. Getting there...Closer to being able to start on the brake system anyway.

3. While on jack stands...looked at taking out the charcoal canister and now unused lucas ignition coil. Think I'm going to stick with the pertronix dizzy and coil...seems to be running just fine. Old dizzy is really knackered: the wiring inside (cloth covered) is all deteriorating to where you can see the copper...the old retard capsule was just hacked off the body. Thinking it can be renovated and kept Just In Case, but with a low-impedence coil now in the car...may have to rebuild and upgrade to a pertronix module. Right now? Threw it in the 'removed bits' bin. Got other things to do.

More later...

[ add comment ] ( 91 views )
Starter and Timing Success 
Got the starter in today. Whomever installed it the last time must have used an air ratchet to tighten it down...had to pull out the 24" breaker bar and 9/16ths impact impact socket to break the bottom bolt loose. It's all good now; RD had clocked the starter on the mounting flange and it all went together just fine. Just to protect the leads, used a light coat of penetrox (which I use when building antenna installs on towers to prevent corrosion; it says it's good for CU/AL, AL, and SN connections, so, thinking it's just fine for what we use it for...)

Needed to freshen up all the power connections; pulled a lead off to carry the 12V up along the bundle so I have a place to provide power for my remote start switch (the white/red lead for the starter solenoid was modified with a Y lead for the other lead off the remote button). Cleaned up the wiring at the coil side, and behold, the tach started working properly rather than bouncing around. Amazing what fresh crimp connections on tinned leads will do for connection goodness. Yes, I know about embrittlement of solder on copper, etc. Takes years though...so, like using galvenized versus stainless piping for the radiator transfer pipes...it will be an issue long after I'm sitting on the porch in my bathrobe yelling at kids to get off my lawn...lol.

Next up...VCG, timing, new dizzy, new coil, timing. What say the tribe about which sealant to use on the cork gasket? Wilkins says a thin coat of RTV on the D plugs (all three are leaking nicely, so going to replace them too...). Aviation form-a-gasket (which I have...and we use to seal case halves on Lycoming and Continental aircraft engines...and a silk thread laid in it, believe or not...) or some other goop?

Next next up: have new spitfire .70 MC coming and Ezbleed pressure bleeder. Thinking at this point, going to disconnect all the bundys going to the wheel cylinders, rebuild the calipers with stainless pistons I have on hand and new seal kits and greenstuff pads on the way, hook up drain lines to all the cylinders, open them all up and flush the old fluid out after replacing the MC, then put all back together. Replace the original rubber hoses with new armored hose, and redo the pipes on the top of the rear trailing arms. They look like they've been manhandled along the way, and I still have 22' of nickle/copper pipe to use..

[ add comment ] ( 102 views )

<<First <Back | 1 | 2 | 3 | 4 | 5 | Next> Last>>